Etc light board manual

 

 

ETC LIGHT BOARD MANUAL >> DOWNLOAD LINK

 

ETC LIGHT BOARD MANUAL >> READ ONLINE

 

 

 

 

 

 

 

 

 

 

To make sure the board is set up for the tutorial, do this: (I'll explain many of these settings later) Press Setup Press 1(System Settings) Press 1(Number of Dimmers) Enter Type 300 Enter Express Tutorial Version 1.0 © 2003 nmm 2 Press 2 (Number of Channels) Enter Type 48 Enter(you could leave this number set higher if you want—it won't matter. Desk Light Dimmer 2. RFU fuse (T2.5A) 3. RFU 4. DMX512 Out (2 universes) 5. ETCLink 6. Disk Drive (side) 7. Power switch 8. Power input connector 9. Command Display output 10. Parallel Printer 11. Remote Macros 12. MIDI In/Out/Thru 13. ETCNet (newer facepanels do not have Thin-net connector) 10 9 8 0 4 3 2 1 PUS H 1. Desk Light connectors 2 November 8, 2007 by Rob Sayer The lighting control, "board" or "desk" is the a key part of any stage lighting set up and it is using the lighting desk that an operator is able to control the equipment. This can range from adjusting the "levels" on stage lighting dimmers to controlling complex intelligent lighting systems and media servers. The jumper SPEED is responsible for manual selection of the device speed. If the ID3 jumper is closed and SPEED jumper is closed, then configuration of device is possible with Light Client but a firmware upgrade is not possible. We strongly recommend using the Light Client software to configure device parameters as well as device speed. Stage Lighting for Students. Lighting Control. Types of Consoles. There are many types of lighting consoles, for different purposes. Most fall into one of these categories. Manual Consoles: The simplest board you are likely to encounter is a manual two-scene preset board. This console has two or more rows ("presets") of faders and a crossfader Expression Two Scene Preset User Manual, v.3.1 vii Chapter 11 Groups. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 I've got most of my washes and scene lighting and cues set up for a theatre show. I've got 4 MAC 250+ Entours connected to the board. Channels 130-133. I've added those 4 channels into group 1. I've also set up a bunch of palettes for intensity, beam, color, and focus. I'm just not really sure what the best way to program these into my board is iv Contents Chapter 3 System settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Setting the number of dimmers Use two screws to connect the vertical piece of wood to the horizontal piece of wood and repeat on the other side. (4 screws used) 4. Stand the lightboard up and drill three holes connecting the foot of the lightboard to the vertical post, repeat on the other side (total of 6 screws used) 5. Using a piece of the 8in steel connect the vertical TIME-BASED DAYLIGHTING MANUAL OCCUPANCY = 5 1.2SYSTEM ARCHITECTURE The nLight architecture is based on the five underlying concepts defined in this section: • nLight Enabled Device • nLight Control Zone • nLight Channels • nLight Operational Modes • nLight Backbone 1.2.1 nLIGHT ENABLED DEVICE 2 Element User Manual Welcome to Element Thank you for purchasing your Element from ETC! This introduction to Element will list all the various helpful tools available to you. In addition to this User Manual, Element also has video tutorials, an online user forum dedicated completely to Element, and support from ETC Technical Services. N Scale Centipede Sideframe Removal and Driver Installation - August 16, 2015. K7 Sound Stock Car Instructions - August 16, 2015. DCC Observation Car Light Board Extended User Manual - January 31, 2013. DCC Lighting-Equipped Observation Car Instructions - January 30, 2013. Resetting your Paragon2 Sound-equipped Locomotive - December 16, 2010. N Scale Centipede Sideframe Removal and Driver Installation - August 16, 2015. K7 Sound Stock Car Instructions - August 16, 2015. DCC Observation Car Light Board Extended User Manual - January 31, 2013. DCC Lighting-Equipped Observation Car Instructions - January 30, 2013. Resetting your Paragon2 Sound-equipped Locomotive - December 16, 2010. 2 SmartFade v1.5 User Manual Using this Manual Congratulations on your purchase of the SmartFade control console. The following configurations of SmartFade are available. • SmartFade 1248, which provides 12-channel basic Two Scene operation, 48-channel Normal mode for manual and memory playback, and DMX Backup mode for capturing Getting Started. Follow these steps to make your sound visual. Connect the HDMI Out port to a powered-up HDMI® monitor.; Connect the power adapter to a power outlet, and then connect its plug to the 9VDC power port, the leftmost port on the back of ETC. The top row's Status LED will indicate progress, glowing light blue as ETC is booting up, and then white when things are operational. ETC Ion XE20 with fader wing. A lighting control console (also called a lightboard, lighting board, or lighting desk) is an electronic device used in theatrical lighting design to control multiple stage lights at once. They are used throughout the entertainment industry and are normally placed at the front of house (FOH) position or in a

602, 613, 172, 661, 851.